How to Remove and Also Replace a Bath Tub
How to Remove and Also Replace a Bath Tub
Blog Article
They are making a few good pointers related to A Step-by-Step Guide to Installing a Bathtub in general in the article which follows.
Mounting a bathtub isn't specifically rocket science, however it does require strong plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old bath tub with a new one is additionally a moderately tough task. If the old tub is easily obtainable, the project can relocate immediately; if you have to open a wall surface to remove the old tub and also position the new bath tub, the task is much harder. In either instance, the task is within a house handyman's skills, although you will certainly need a helper to leave the old bathtub and embeded in the brand-new one. See to it you have qualified yourself for the task and also are comfortable trying it. As opposed to employing a specialist to take over a halfway-completed job, it is far better to consider utilizing one prior to you start. Opportunities are you may need a specialist plumber to make tube connections.
This short article will certainly aid you install a new bath tub in your washroom if you have actually currently purchased a brand-new bathtub and also don't need to transform the arrangement of your previous supply of water pipelines.
Your devices and also material checklist should comprise the following:
Getting ready for the Setup
First of all, the supporting framework provided with the bathroom must be fitted (if called for) according to the maker's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is very important to see to it that if the faucet features a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps unit to prevent pressure on the bath tub.
Fit the versatile tap ports to the bottom of both faucets utilizing 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet via the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you utilize all of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath ought to now be ready to be suited its last setting.
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you ought to do is disconnect the water supply. After doing so, turn on the faucets to drain pipes any type of water staying in the system. The process of removing the existing faucets can be rather troublesome due to the restricted accessibility that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a cloth ready for the continuing to be water that will certainly come from the pipelines. As soon as the supply pipes have been gotten rid of, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from turning throughout this procedure. Once the faucets have actually been removed, the holes in the bath/basin will need to be cleaned of any kind of old securing compound.
Prior to proceeding to fit the brand-new taps, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is needed for the new taps to fit.
Mounting the Bathtub
Making use of the two wooden boards under its feet, put the bathtub in the called for setting. The wood boards are valuable in equally spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four little points.
The following goal is to make sure that the bathtub is leveled all round. This can be accomplished by checking the spirit level and also adjusting the feet on the bath tub until the level reads degree.
To install taps, fit all-time low of the furthest adaptable tap port to the appropriate supply pipe by making a compression sign up with; then do the exact same for the various other tap.
Turn on the water supply as well as examine all joints and brand-new pipework for leakages and tighten them if essential. Fill the tub and additionally check the overflow outlet and also the normal electrical outlet for leakages.
Finally, take care of the bathroom paneling as described in the maker's instruction manual. Tiling as well as securing around the bath tub should wait up until the bath tub has actually been used a minimum of when as this will certainly settle it into its last placement.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic adapter to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap and the various other end supplies a link to the existing supply pipelines.
If you need to fit a monobloc, then you will need minimizing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, position the faucet in the installing opening in the bath/basin ensuring that the washers are in place between the faucet and also the sink. Safeguard the tap in place with the manufacturer offered backnut. When the faucet is firmly in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with typical faucet ports. The previous kind needs to be attached to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the area where the bathroom satisfies the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to fracture an inflexible seal, creating the water to permeate the wall in between the bath and the tiling, resulting in problems with dampness and also feasible leakages to the ceiling listed below.
You can pick from a range of coloured sealers to blend in your fixtures and fittings. They are sold in tubes and also cartridges, and also can sealing spaces up to a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with spins of drenched paper or soft rope. Keep in mind to always fill the bath tub with water prior to securing, to enable the movement experienced when the tub remains in usage. The sealant can break fairly very early if you do not think about this activity before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally quickly available on the market. It is a good idea to fit the ceramic tiles using waterproof or water resistant sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed our post about How to Install a Bathtub. Thanks so much for finding the time to read our blog post. Enjoyed our blog posting? Please share it. Help someone else find it. We recognize the value of reading our article about How to Install a Bathtub Yourself.
Contact Us
Report this page